Blog

Oct 09, 2023

Electro

Scientific Reports volume 13, Article number: 16803 (2023) Cite this article 263 Accesses 4 Altmetric Metrics details An electrochemical sensory platform is presented for determination of sumatriptan

Scientific Reports volume 13, Article number: 16803 (2023) Cite this article

263 Accesses

4 Altmetric

Metrics details

An electrochemical sensory platform is presented for determination of sumatriptan (SUM) in aqueous solutions and human blood serum. A pencil graphite electrode (PGE) was electrochemically delaminated by cyclic voltammetry technique, and then further modified using nanoparticles of a zinc-based metal–organic framework (Zn(II)-MOF). The fabricated Zn(II)-MOF/EDPGE electrode was utilized for sensitive electrochemical detection of SUM via an electro-oxidation reaction. The Zn(II)-MOF was hydrothermally synthesized and characterized by various techniques. The electrochemical delamination of PGE results in a porous substrate, facilitating the effective immobilization of the modifier. The designed sensor benefits from both enhanced surface area and an accelerated electron transfer rate, as evidenced by the chronocoulogram and Nyquist plots. Under optimized conditions, the developed sensor exhibited a linear response for 0.99–9.52 µM SUM solutions. A short response time of 5 s was observed for the fabricated sensor and the detection limit was found to be 0.29 μM. Selectivity of Zn(II)-MOF/EDPGE towards SUM was evaluated by examining the interference effect of codeine, epinephrine, acetaminophen, ascorbic acid, and uric acid, which are commonly found in biological samples. The developed sensor shows excellent performance with recovery values falling within the range of 96.6 to 111% for the analysis of SUM in human blood serum samples.

Sumatriptan (SUM; IUPAC name: 1-[3-(2-Dimethylaminoethyl)-1H-indol-5-yl]-N-methyl-methanesulfonamide) is the first clinically available tryptamine-based drug which is commonly used to treat acute migraine attacks1. The compound, classified as a serotonin agonist, targets the 5-HT1D and 5-HT1B receptors, effectively mitigating vascular inflammation associated with migraine2. It is found that after oral administration of a sumatriptan 50 mg tablet, the maximum concentration in human blood plasma (Cmax) is 33.21 ng/mL (0.11 μM) after tmax of 1.13 h and the elimination half-life (t1/2) is 2.96 h3. It is worth noting that high doses of SUM (200 mg day−1) may lead to sulfhemoglobinemia, the situation in which the addition of sulfur into the hemoglobin molecules occurs and the blood color changes from red to greenish-black4.

Due to the physiological importance of SUM, extensive efforts have been devoted to determining this compound in biological samples. Among the diverse analytical methods available, liquid chromatography has been advised as a typical technique, and diverse liquid chromatographic techniques such as HPLC5,6,7, UPLC8, and HPTLC9 have been developed for its measurement. Additionally, alternative methods including micellar electrokinetic chromatography10, conductometry11, UV–Vis spectrophotometry12,13, capillary electrophoresis14, and fluorescence spectroscopy15 have been explored in the literature for determination of SUM. Despite notable sensitivity in some cases, these methods often suffer from tedious and time-consuming procedures, and high costs, which require specific standards, complexing agents, or even toxic solvents for analysis. Consequently, there is a compelling need for the development of sensitive, cost-effective, rapid, and straightforward approaches for the determination of SUM. These characteristics find fulfillment in electrochemical sensors, as previous studies have demonstrated the electrochemical activity of SUM16. Accordingly, some efforts have been invested in development of electrochemical sensing platforms for the sensitive determination of SUM.

Following the pioneering work by Sagar et al.16, which employed a glassy carbon electrode (GCE), subsequent researchers have used chemically modified electrodes to facilitate electron transfer between the electrode surface and SUM as the analyte, thereby enhancing detection sensitivity. Notable examples include the application of pyrolytic graphite electrode improved by multi wall carbon nanotubes (MWCNTs) decorated with silver nanoparticles17, carbon-paste electrode modified with a Cobalt Schiff-base coordination complex and MWCNTs18, ion-selective electrode incorporating dioctyl phthalate within carboxylated polyvinyl chloride matrix19, and carbon paste electrode modified by ultrasonic-electrodeposited Pt nanoparticles on ZrO2 nanoparticles20. Furthermore, various modifications of GCE (such as bilayer structures consisting of MWCNTs/polypyrrole21, Cu nanoparticles/poly-melamine22, and self-assembled MXene-MWCNT-chitosan23) have also been explored. In all cases, modified electrodes have consistently outperformed their unmodified counterparts in SUM determination.

Pencil graphite, one of the most extensively used electrode materials, is known for its significantly low detection limits, low background signal, high sensitivity and reproducibility, modifiable electroactive surface area, cost-effectiveness, and disposability. Therefore, the pencil graphite electrode (PGE) has attained significant consideration in recent years as a valuable alternative for traditional expensive electrodes24,25. The literature survey underscores that the electrocatalytic properties of PGE can be improved by modifying the electrode with suitable electrocatalyst/electron mediators26,27,28,29,30, as well as electrochemical pretreatment31,32, and delamination33. Notably, numerous efficient electrochemical sensor platforms for the determination of various compounds in biological samples have been presented on the base of PGE and electrochemically treated PGE34.

In the realm of analytical techniques, the development of electrochemical electrodes has shown remarkable growth due to their versatility and affordability. Therefore, electrodes with new nanocomposite interfaces have emerged35,36,37,38,39,40,41,42. On the other hand, metal–organic frameworks (MOFs), which are porous coordination polymers consisting of metal-based nodes and multitopic organic ligands, have been applied as electrode modifier materials. Due to their porous nature, ease of tailoring, ease of modification with various organic dyes and nanostructures, high mechanical stability, conductivity, and catalytic properties, MOFs have received significant attention as electroactive interfaces for electrochemical sensors43. Electrochemical treatment of PGE in a mixture of melamine and ammonium sulfate has been reported for in-situ synthesis of sulfur and nitrogen co-doped graphene nanocomposite on PGE (SNDGr/PGE). The obtained SNDGr/PGE was utilized as a support for the electrodeposition of Cu-MOF by applying a suitable cathodic potential44. The electrodeposition technique was also used in the fabrication of a binder-free cobalt-doped Ni-MOF film on GCE for direct sensing of levofloxacin45. Also, core–shell Fe3O4@ZIF‑8 nanoparticles (ZIF-8 = Zeolitic imidazolate framework-8) immobilized on screen printed graphite electrode has been utilized for voltammetric sensing of sumatriptan in the presence of naproxen in aqueous solutions46.

In numerous studies, MOFs have been immobilized on the electrode surface by the casting method to fabricate the chemically modified electrodes47. Moreover, in some cases, supporting materials have also been added48,49,50. However, we suppose that by electrochemical treatment of PGE, MOF nanoparticles could efficiently be immobilized on the electrode surface. In this method, the electron transfer rate enhances while the supporting material is not required51.

Here, a simple, cost-effective, and straightforward electrochemical sensor is introduced for the determination of SUM in biological fluids. {[Zn4(1,4-bdc)4(bpda)4]0.5DMF.3H2O}n (Zn(II)-MOF, where 1,4-bdc = 1,4-benzene dicarboxylate, bpda = N,N′-bis(pyridine-4-yl)-1,4-benzenedicarboxamide) is a two-fold interpenetrated amide-containing MOF with open-ended channels52,53. The compound has previously been investigated for CO2 adsorption within its open-ended channels. However, more recently, it has been utilized through a simple casting method to fabricate a modified screen-printed carbon electrode (SPCE) which applied for the measurement of Fentanyl47. In this work, hydrothermally synthesized Zn(II)-MOF (as a modifier) was drop-casted on the surface of an electrochemically delaminated PGE (EDPGE). Electro-catalyzed oxidation of SUM on the surface of Zn(II)-MOF modified EDPGE was investigated for determination of the compound in biological matrices. The fabricated sensor exhibits a linear response in the concentration range of 0.99 to 9.52 µM for SUM solutions in human blood serum. To the best of our knowledge, the introduced Zn(II)-MOF/EDPGE sensor has not been employed for the determination of SUM previously.

All reagents and solvents used, except for sumatriptan, were of analytical grade and were purchased from Merck and Sigma Aldrich Companies (Germany) and used as received without any further purification. Zinc chloride (ZnCl2, 99.9%), dimethylformamide (DMF, anhydrous, 99.8%), 2-amino-1,4-benzene dicarboxylic acid (NH2BDC, 2-aminoterephthalic acid, 99%), sodium hydroxide (NaOH, 99.9%), potassium chloride (KCl 99.9%), potassium hexacyanoferrate (III) (K3[Fe(CN)6] , 99.9%) were used through the study. N,N′-Bis(4-pyridinyl)-1,4-benzenedicarboxamide (BPDA, Purity: > 99%) was synthesized according to the previously reported method54. The raw material of sumatriptan (brand name: Imitrex) with a purity of 99.9% was obtained from Tehran-Shimi Company (Iran). A stock solution (2 mM) was prepared by dissolving 29.54 mg of SUM in 50 mL of deionized (DI) water. A 0.1 M KCl solution containing 1 mM [Fe(CN)6]4−/3− was applied for the electrochemical impedance spectroscopy (EIS) studies. The respective Materials Safety Data Sheets (MSDSs) are given in supplementary information.

For electrochemical experiments, a PGSTAT-12 potentiostat/galvanostat device (ECO Chemie, Netherlands) equipped with GPES software was used. In addition, electrochemical impedance spectroscopy (EIS) was performed by Ivium potentiostat/galvanostat (CompactStat.h, Ivium Technologies BV) linked to Ivium software. For electrochemical research work, a pencil core with diameter of two mm and HB hardness (German Routing Company) was used. The modified pencil graphite was used as the working electrode. An Ag/AgCl and a Pt wire were used as reference and counter electrodes, respectively. All electrochemical measurements were performed at room temperature.

The synthesized materials and the electrode surface were characterized using FTIR, SEM, XRD, TGA, and EDX techniques. The infrared spectrum (FTIR) was recorded, in the range of 4000–400 cm−1, using KBr pellets on a Win-Bomem spectrometer (Version 3.04 Galatic Industries Corporation and Thermo Nicolet Nexus 670). To identify the synthesized compounds, Powder XRD (PXRD) data were collected at 297 K on Bruker D8 Advance equipped with CuKα radiation (λ = 0.15406 nm). Scanning electron microscopy (SEM) images and EDX analyses were recorded using a ProX model SEM (Netherlands) with a gold coating thickness of up to several angstroms.

Zn(II)-MOF was synthesized according to the previous reports47,52. Figures 1 and 2a schematically shows the synthesis steps. Bis-(4-pyridinyl)-1,4-benzene dicarboxamide (BPDA, 0.15 mmol, 47.8 mg), 2-amino-1,4-benzene dicarboxylic acid (BDC NH2, 0.15 mmol, 47.8 mg) and ZnCl2 (0.15 mmol, 20.5 mg) were dissolved in 0.5 mL of water and 7 mL of DMF. The resulting solution was then transferred to a Teflon-lined autoclave and heated at 120 °C for 72 h. After cooling, Zn(II)-MOF was precipitated as a powder which was filtered, washed with water and ethanol, and left to air-dry at room temperature. IR (KBr): ν = 3466 (m), 3366 (m), 3085 (w), 1677 (s), 1597 (vs), 1569 (s), 1503 (s), 1430 (s), 1379 (s), 1332 (s), 1298 (s), 1261 (m), 1211 (m), 1119 (m), 1017 (m), 890 (m), 834 (m), 712 (m), 603 (m), 538 (m) cm−1.

The balanced reaction equation of the hydrothermal synthesis reaction.

Schematic illustration of the synthesis of Zinc(II)-MOF (a) and Preparation of Zn(II)-MOF/EDPGE (b).

A schematic representation of the preparation of the modified electrode is given in Fig. 2b. To create a cost-effective sensor, a pencil lead was used as the base of the electrode. The electrode was prepared in a two-step procedure. First, the PGE was delaminated through an electrochemical method. To establish an electric current, a copper wire was attached to the end of the pencil lead, and the entire electrode body was insulated with Teflon tape. Subsequently, the electrode surface was polished using soft sandpaper and thoroughly rinsed with distilled water. Then, the pencil graphite electrode was immersed in an electrochemical cell containing 0.8 M sodium hydroxide solution. The electrode surface was activated using the cyclic voltammetry (CV) technique and applying the potential in the range of + 1.3 to + 1.9 V. The electrochemically delaminated pencil graphite electrode (EDPGE) was achieved after 50 cycles.

In the next step, to prepare the Zn(II)-MOF/EDPGE, Zn(II)-MOF was deposited onto the EDPGE surface. To prepare a uniform dispersion of the Zn(II)-MOF nanoparticles in water, 10 mg of the synthesized compound was added to 5 mL of distilled water and subjected to ultrasound waves for 1 h. 5 μL of the prepared water-dispersed Zn(II)-MOF nanoparticles was drop-casted on the prepared EDPGE. The electrode was left to air-dry for 24 h before use.

Human blood was obtained from the Pasteur Laboratory (Khoy, Iran) and stored in a refrigerator for 24 h to allow for clotting before use. To strip and remove proteins, 1.5 mL of methanol was added to 2 mL of blood serum. The resulting mixture was centrifuged for 10 min at 3000 rpm to separate the clear solution. Subsequently, the solution was filtered through a 0.2 µm syringe filter. The filtered solution was then brought to a volume of 10 mL with phosphate buffer (pH = 7). The resulting matrix was used for the analysis of SUM using spike studies55.

All experiments and methods conducted throughout this study strictly adhered to relevant guidelines and regulations. In addition, it is confirmed that all participants involved in this research signed informed consent. Furthermore, it is declared that all research and methods involving human subjects were carried out in accordance with the ethical standards and regulations of the Ethical Committee of the Urmia University of Medical Sciences, Urmia, Iran, under permission number 3-235686, granted on July 12th, 2021. Before their participation, the volunteers received comprehensive information about the experimental aspects of the study. They were assured of anonymity in the experimental process and also the publication of results exclusively for scientific purposes.

The morphology of the hydrothermally synthesized Zn(II)-MOF was examined by scanning electron microscopy (SEM). As shown in Figs. 3a and aʹ, under hydrothermal conditions, micrometer-sized plate-like crystals were formed by aggregation of Zn(II)-MOF nanocrystals.

SEM images (a, 5000 × and aʹ, 200,000 ×), XRD pattern (b), and TGA (c) for the synthesized Zn(II)-MOF.

The FTIR spectrum of the synthesized Zn(II)-MOF is shown in Fig. S1 in the supplementary information. The observed bands in the measured spectrum of the compound are in accord with the previously reported values52. The lattice water ν (O–H) stretching vibration is observed as a broad medium band at 3466 cm−1. The ν (N–H) stretching band is found at 3366 cm−1. The band at 3064 cm−1 is due to the aromatic ν (C–H) stretching vibration. The amide N–H bending vibration is observed as a strong band at 1677 cm−1. The very strong band at 1597 cm−1 and the strong band at 1569 cm−1 are attributable, respectively, to ν (C=N) and ν (C=O) stretching vibrations. The carboxylate COO bending vibrations observed as a strong band at 1332 cm−1. Also, the C–O stretching vibration is observed at 1119 cm−1.

The measured PXRD pattern of the synthesized Zn(II)-MOF (Fig. 3b) is comparable with previous reports47,52,56, and confirms successful synthesis of the desired compound. The measured PXRD data was analysed using Reflux module of Materials studio (v8, Accelrys)57. Crystal structure (cell parameters, atom positions, and temperature factors) determined by single crystal XRD analysis52 was used for Rietveld refinement58,59 of the crystal structure against experimental PXRD data. In the previously reported single crystal structure52, the hydrogen atoms were appropriately adjusted on C and N atoms in calculated positions Materials studio57. The water hydrogen atoms were ignored in the refinement. Fractional coordinates of atoms were fixed and the temperature factors, calculated by single crystal x-ray diffraction, were not refined. Only the measure PXRD data in the range of 2θ = 8.00–45.00° were included in the refinement. Cell parameters were refined and the final refinement yielded the residuals Rp = 13.95% and Rwp = 17.99%. For the monoclinic unit cell (space group: P21/c), the Rietveld refined lattice parameters [single crystal x-ray results52] are: a = 20.21525(± 0.00685) Å [20.1818(3) Å], b = 31.33971(± 0.00598) Å [30.2868(5) Å], c = 19.62813(± 0.00784) Å [19.7451(3) Å], and β = 89.14761(± 0.06117)° [90.6880(6)°]. Figure S2 in the supplementary information shows the final Rietveld plot for the refinement of Zn(II)-MOF. Also, the crystal packing of Zn(II)-MOF is given in Fig. S3 in the supplementary information. A Reflex summary report for the final Rietveld refinement of Zn-MOF and the crystal structure of the compound (in cif file format) are provided as the supplementary material. In the measured PXRD pattern, the reflection peaks observed at 2θ (indexed as) = 8.52° (1 2 −1), 9.08° (0 0 2), 11.4° (2 2 −1), 13.2° (3 0 0), 14.52° (0 4 2), 17.72° (0 4 3), 18.16° (1 6 −1), 22.76° (0 8 0), 24.56° (0 8 2) and 26.56° (0 8 3).

The thermal stability of the synthesized MOF was evaluated using TGA technique (Fig. 3c). In an inert atmosphere, the sample undergoes weight loss in four steps, which is a typical behavior observed for a mixed ligand containing MOF60. In the first step, between 100 and 300 °C, lattice water and DMF molecules leave the porous network of Zn(II)-MOF (weight loss of 17.17%). In the second step, a weight loss of 18.4% was observed at 300–370 °C which is related to the removal of BDC NH2. In the third step, the weight loss of 31.17% at 410–460 °C could be attributed to the elimination of BPDA and BDC NH2. Finally, between 470 and 700 °C, a weight loss of 32.11% occurs corresponding to the decomposition of BPDA. Since the test was performed in the absence of oxygen, the final product is zinc which is in accord with the theoretical value of 2.69%53.

The surface structure and morphologies of the unmodified/modified electrodes were surveyed by scanning electron microscopy (SEM). As shown in Fig. 4a, at the micrometer scale, the bare PGE has a relatively smooth cloud-like surface with no porosity. In comparison, graphite sheet fractures are visible for EDPGE (Fig. 4b), indicating that the electrochemical delamination has been performed successfully. The observed surface feature is consistent with previous studies33,44. Figure 4c illustrates that the EDPGE surface is effectively modified by the synthesized Zn(II)-MOF. The compound is well dispersed on the EDPGE surface and especially within its porous layers. Zn(II)-MOF nanoparticles are deposited throughout the surface of the electrode as porous lumps.

SEM images of the surface of pencil graphite electrode (PGE) (a, aʹ), the electrochemically delaminated electrode (EDPGE) (b, bʹ) and the final modified electrode (Zn(II)-MOF/EDPGE) (c, cʹ); EDS mapping of elements C (d), N (e), O (f) and Zn (g) and EDX analysis of Zn(II)-MOF/EDPGE (h).

The energy dispersive spectroscopy (EDS) analysis was used to identify the constituent elements of the sample and to determine their relative weight percentages. Figure 4d–g depict EDS mapping analysis results, indicating the even distribution of the constituents’ elements including Zn, O, N, and C on the surface of Zn(II)-MOF/EDPGE. The EDX spectrum for the Zn(II)-MOF/EDPGE surface is shown in Fig. 4h. The presence of Zn, O, N, and C elements are confirmed and surface elemental analysis results are: C 42.06%, N 18.92%, O 36%, and Zn 2.47%. The Zn content is in good agreement with the value obtained from the TGA (2.69%).

Electrochemical Impedance Spectroscopy (EIS) is a very sensitive technique for the analysis of changes in electrode surface properties resulting from modifications. Also, it is useful to clarify the mass and charge-transfer, as well as diffusion processes at the electrode surface61. Figure 5a shows the Nyquist plots for PGE, EDPGE, and Zn(II)-MOF/EDPGE measured using Fe(CN)63−/4−(1 mM)/potassium chloride (0.1 M) solution.

Nyquist plots of PGE, EDPGE, and Zn(II)-MOF/EDPGE measured in 0.1 M KCl solution containing 1 mM [Fe(CN)6]−3/−4 (inset: the equivalent Randles circuit model; the fitted Nyquist curves are given as solid black lines) (a) The respective bode plots depicting the magnitude changes vs frequency (b) and phase angle changes vs frequency (c).

According to the obtained equivalent circuit (Fig. 5a), the following equation governs the behavior of impedance in the complex plane:

By removing the frequency parameter in the real and imaginary components, the following equation is obtained which governs the impedance behavior in the complex plane.

Since \(X<0\), this equation describes a half-circle in the lower complex plane with the following center and radius.

The calculations were done as follows:

The equivalent Randles circuit model is depicted in the inset of Fig. 5a, which schematically describes the electrochemical processes at the interface surface. The fitting parameters for the studied electrodes are provided in Table 1. The Rs, Rct or Rp, W and C, respectively, are voltage source resistance, charge transfer resistance, parallel resistance, Warburg impedance and the double-layer capacitance (Cdl)62.

The Nyquist plot of the PGE consists of a semicircular section with a large diameter followed by a straight line. Accordingly, the charge transfer resistance (Rct) value for bare PGE was estimated to be 8245.55 Ω. In comparison, the electron transfer rate for EDPGE is enhanced and the Rct was reduced to 3541.74 Ω. On the other hand, by depositing Zn(II)-MOF on the active sites of the EDPGE, the electron transfer resistance decreases considerably to a value of 705.38 Ω. The EIS measurements indicate that step-by-step modification of PGE results in the enhanced charge transduction rate, accelerated electrode kinetics, and increased conductivity at the electrode interface.

A Bode plot is the second main format for graphical representation of the impedance data and is used to identify charge-transfer processes63. It is a powerful tool to study the frequency response of a system. By changing the frequency, the reactance occurred between the two interface plates is investigated to understand the changes in the apparent impedance. Figures 5b and c represents the bode plots for PGE, EDPGE, and Zn(II)-MOF/EDPGE. Bode plots in the form of phase angle (θ) versus frequency (Fig. 5c) are characterized by a well-defined peak corresponding to one distinct relaxation process64. Here, Bode plots clearly confirm the Nyquist plot findings.

Figure S4A in the supplementary information gives the chronocoulograms for bare PGE, EDPGE, and Zn(II)-MOF/EDPGE, recorded in Fe(CN)63−/4− (1 mM) solution. The electrochemical active surface area of all electrodes was calculated using the Cottrell equation65:

where Qdl and Qads are, respectively, the charge of double-layer and adsorbed species, n is the number of electrons exchanged in the reaction, A is the surface area of the electrode (cm2), C is the solution concentration (mol cm−3), and D is the diffusion coefficient (cm2 s−1). The Q vs. t1/2 graph is shown in Fig. S4B in the supplementary information. The slope values calculated for bare PGE, EDPGE, and Zn(II)-MOF/EDPGE are 4.79, 9.76, and 19.60, respectively. Also, the calculated electrode surface area (A) values are 0.016 cm2, 0.0322 cm2, and 0.065 cm2 for bare PGE, EDPGE, and Zn(II)-MOF/EDPGE. Accordingly, the surface area of EDPGE and Zn(II)-MOF/EDPGE are approximately two and four times higher than that of bare PGE. Such a property is a prerequisite for the development of highly sensitive sensors.

Cyclic voltammetry has been widely used to study electron transfer processes, the effect of chemical reactions on electrode surface electrochemical processes, as well as to evaluate stability properties and electrocatalytic activities66. To assess the electrocatalytic activity of the synthesized Zn(II)-MOF, acting as a surface modifier of EDPGE in the electro-oxidation of SUM, cyclic voltammograms of the bare PGE, EDPGE, and Zn(II)-MOF/EDPGE (in 0.1 M phosphate buffer at pH 7) were measured in the absence and presence of SUM (90.9 μM) (see Fig. 6a). In the absence of SUM, no electrochemical signal was observed for the bare PGE. However, in the presence of SUM, a weak oxidation signal at 0.81 V with a current of 1.025 µA was detected (Fig. 6a, curve a). In comparison, for the EDPGE, the background current was significantly increased due to the augmentation of the electrode's active surface (Fig. 6a, curve b).

Cyclic voltammograms for bare PGE, EDPGE, and Zn(II)-MOF/EDPGE measured in 0.1 M phosphate buffer (pH = 7) in the absence and presence of SUM (90.9 μM) (a) and cyclic voltammograms in 0.1 M phosphate buffer solution in the presence of SUM (50.7 μM) at different scan rates (10–100 mV/s) (inset: Changes in the anodic peak current vs. the scan rate) (b).

By electrochemical pretreatment process, various oxygen-containing functional groups are formed on the surface44. Moreover, the process leads to the formation of graphite sheet fractures due to the penetration of OH− groups and solvent molecules into the graphite layers33. The expansion of graphite sheet fractures exposes new layers to oxidation, resulting in an excellent surface for the deposition of the synthesized MOF. By adding the analyte to the buffer, the electro-oxidation signal increases, while the overvoltage is reduced due to the pretreatment of the electrode. Cyclic voltammograms of the Zn(II)-MOF/EDPGE in the absence and presence of SUM are illustrated in Fig. 6a, curve c. Due to the formation of active sites on the surface of Zn(II)-MOF/EDPGE, compared to the PGE and EDPGE, the resulting signal is significantly amplified. As a result, the current intensity is approximately 20 times greater than that observed for the bare PGE.

The amount of the electrode modifier compound and the accumulation time are the most important factors which affect the electrode performance. To optimize these parameters, 1, 3, 5, 10, and 15 μL of the prepared Zn(II)-MOF suspension (10 mg in 5 mL H2O) were pipetted and deposited on the EDPGE surface. The highest sensitivity of Zn(II)-MOF-modified EDPGE was achieved with 5 μL of the suspension. For this electrode, the anodic peak current reached its maximum value (see Fig. S5A in the supplementary information) may be due to the availability of the active microscopic surface for the adsorption and oxidation of SUM. By increasing the used suspension volume to 10, and 15 μL, the anodic peak current decreases. By using larger volumes of the modifier a thicker layer forms on the electrode surface resulting in the supersaturation of the adsorbed analyte molecules on the electrode surface. This phenomenon passives the electron transfer and electrode resistivity increases, which reduces the electrode response to the analyte67.

To investigate the effect of scanning rate, cyclic voltammograms of SUM were recorded using the working electrode at scan rates ranging between 10 and 100 mV/s. As shown in Fig. 6b, the anodic peak currents increase with higher scan rates, and the anodic peak potential shifts towards more positive potentials. Moreover, the oxidation and reduction peak currents in the measured cyclic voltammograms are found to be asymmetric. This observation suggests that the reaction is irreversible. In addition, it is found that the anodic current changes linearly with the scanning rate (see inset in Fig. 6b) indicating that the electrochemical reaction mechanism depends on the adsorption of electroactive species on the electrode surface68. The adsorption-based electro-oxidation of SUM has also been reported, previously, using MXene-MWCNT-chitosan/GCE23 and Pt-ZrO2 NPs/CPE20.

Since the electro-oxidation of SUM on Zn(II)-MOF/EDPGE surface follows an adsorption-depended mechanism, the accumulation time would be a crucial parameter that affects the electrochemical response of the sensor. The effect of accumulation time on sensor performance was investigated by differential pulse voltammetry (DPV) measurements for 5.82 µM SUM solutions (see Fig. S5B and C in the supplementary information). It is worth noting that differential pulse voltammetry (DPV) is a popular technique that exhibits more sensitive response rather than the CV. This is rooted in the fact that measuring the current for each pulse effectively minimizes the background current. Therefore, this technique is useful in the analysis of trace analytes.

Increasing the accumulation time up to 60 s led to an increase in the oxidation peak current of SUM on the surface of Zn(II)-MOF/EDPGE (Fig. S5B and C in the supplementary information). However, when the accumulation time exceeds 60 s the signal strength decreases due to the electrode surface saturation. As a result, an accumulation time of 60 s was chosen as the optimum duration for the subsequent studies.

The pH value of the supporting electrolyte is the other parameter which affects the electrochemical response of the Zn(II)-MOF/EDPGE. The effect of electrolyte pH on the oxidation of SUM was studied by DPV method in the pH values between 2.0 and 9.0 (Fig. 7). According to the DPV measurements, the best discrimination occurs at pH 7. As a result, the subsequent electrochemical measurements of SUM were carried out in pH 7. In addition, with increasing the solution pH, the SUM oxidation peak potential shifts toward less positive values. This foundation indicates that protons are involved in the oxidation of SUM. A linear relationship between the observed peak potential (Ep) and the pH value of the supporting electrolyte was found. The calculated linear regression equation is Ep (V) = 0.0582 pH + 1.1144 (R2 = 0.9812). The obtained slope value of 0.0582 V/pH is close to the theoretical value of 0.059 V/pH, indicating that an equal number of protons and electrons are involved in the respective electrode reaction.

(A) The pH effect on the DPV measured for 8.61 μM SUM solution using Zn(II)-MOF/EDPGE (supporting electrolyte: phosphate buffer, 0.1 M), (B) Ipa changes with solution pH value, (C) The linear relationship between pH value and Epa.

At optimal conditions, the SUM concentration range for which the fabricated Zn(II)-MOF/EDPGE sensor responses linearly, was determined using DPV method in 0.1 M phosphate buffer solution (Fig. 8a). Pulse amplitude of 50 mV, pulse width of 50 ms, and scan rate of 20 mV/s were applied in the measurements. The calibration curve was obtained by plotting the anodic peak current vs. standard concentrations of SUM, and the regression equation was derived. It was found that when the SUM concentration (CSUM) changes between 0.99 and 9.52 μM, using Zn(II)-MOF/EDPGE, the respective oxidation peak current (ip) increases linearly (Fig. 8). The experimental detection limit for the described sensor was calculated to be 0.29 μM (LOD = 3Sb/m; Sb = the standard deviations for the blank solution and m = the slope of the calibration graph). It should be noted that the DPV method allows investigating the concentrations until the modified electrode surface reaches saturation. After saturation, the active sites on the electrode can be easily reactivated by subjecting the electrode to cyclic voltammetry in the phosphate buffer.

Pulse voltammograms recorded using Zn(II)-MOF/EDPGE in the absence (Blank) and in the presence of SUM (0.99 to 9.52 μM) in 0.1 M phosphate buffer solution (pulse amplitude: 50 mV, pulse width: 50 ms, and scan rate: 20 mV/s) (a) and calibration curve, plotting anodic electro-oxidation peak current vs. SUM concentration (each point shows the average value for three tests ± SD) (b).

Table 2 compares the fabricated Zn(II)-MOF/EDPGE sensor with some previously reported electrochemical SUM sensors17,18,20,21,22,23. Compared to the previous reports, the sensor introduced in this work has excellent features in terms of its straightforward design and cost-effectiveness. Also, it offers favorable characteristics considering its linear range and detection limit. The fabricated sensor benefits from easy and single-step activation of PGE followed by its modification through the casting of Zn(II)-MOF on its surface. As a result of electrochemical delamination, which introduces porosity to the PGE surface, the resulting EDPGE can be easily modified by drop-casting of Zn(II)-MOF. In contrast, the previously reported approaches suffer from multistep electrode preparation.

Selectivity of Zn(II)-MOF/EDPGE sensor for SUM was evaluated by examining the interference effect of some species that could be present in biological samples (see Fig. S6 in the supplementary information). In the presence of codeine (COD), epinephrine (EP), acetaminophen (ACT), ascorbic acid (AA) or uric acid (UA) (38.45 μM), using Zn(II)-MOF/EDPGE, the anodic peak current measured for a 7.70 μM solution of SUM changes within ± 10%. Therefore, these compounds do not interfere with the measurement, and Zn(II)-MOF/EDPGE shows a reasonable selectivity for SUM.

The stability of the sensor was studied by monitoring the current changes every two days. After a two-week storage period at room temperature, the sensor retained 94.25% of its original value, indicating an acceptable stability. To confirm the sensor's reproducibility, five modified electrodes (Zn(II)-MOF/EDPGE) were prepared for determination of SUM in a 7.70 μM solution using the same procedure. The resulting relative standard deviation (RSD) of 2.19% revealed that the proposed sensor exhibits good reproducibility. In addition, to examine the repeatability of the results measured with this sensor, four Zn(II)-MOF/EDPGE electrodes were used to detect the analyte under the same conditions. All four independent sensors exhibited similar responses, and the relative standard deviation (RSD) was 2.6%.

Measurement of SUM in human blood serum was conducted to evaluate the performance of the fabricated sensor in the analysis of real samples. Serum solutions with different concentrations of SUM were prepared according to the described method. The DPVs of the sensor were recorded for the prepared human blood serum samples, and the SUM concentrations were calculated using the corresponding calibration equation (Figs. S7A and B in the supplementary information). All measurements were carried out in triplicates, and the average current values were used in the calibration equation to calculate the standard deviations. By comparing the calculated concentrations with the actual concentrations, the recovery rate of the method for the solutions fell within the range of 96.6–111% (Table 3). According to the results, the fabricated Zn(II)-MOF/EDPGE sensor could successfully measure SUM in serum samples.

In this research study, (Zn(II)-MOF) was hydrothermally synthesized and characterized to evaluate its electrocatalytic performance. The compound was applied as a modifier of EDPGE to fabricate a highly sensitive electro-oxidation sumatriptan sensor. The bare PGE was electrochemically delaminated to enhance the surface porosity and introduce functional groups. Subsequently, a certain amount of the synthesized Zn(II)-MOF was cast onto the prepared EDPGE surface. The Zn(II)-MOF-modified EDPGE was used to detect and measure sumatriptan in standard buffer solution and human blood serum samples. The electrode surface was studied by SEM technique. Also, the electrochemical properties of the fabricated electrode were thoroughly investigated. The electrode exhibits a linear response to the 0.99–9.52 μM solutions of SUM in the standard phosphate buffer (pH = 7) and the detection limit was found to be 0.29 μM. Zn(II)-MOF catalyzes the electro-oxidation of SUM on the EDPGE surface. The synergistic effects of dual electrochemical and electrocatalytic modification of PGE enabled a rapid and sensitive determination of SUM. The fabricated Zn(II)-MOF/EDPGE electrochemical sensor represents advanced features including a high active surface area, excellent analytical characteristics, reasonable selectivity, high sensitivity, low cost, and satisfactory recovery values. These features depict the utility of Zn(II)-MOF/EDPGE as a simple, cost-effective, and rapid sensor for determination of SUM in real samples. We hope that the proposed strategy based on the fabricated electrode may aid in future efforts for routine measurements of the SUM in the real-world. Also this study can pave the way for new strategies in the fabrication of cost-effective sensor arrays to detect and measure other drugs.

The data that support the findings of this study are available from the corresponding author upon request.

Sumatriptan

Pencil graphite electrode

Glassy carbon electrode

Multi wall carbon nanotubes

Metal-organic frameworks

Screen-printed carbon electrodes

Electrochemically delaminated PGE

2-Amino-1,4-benzene dicarboxylic acid

Potassium chloride

Dimethylformamide

Potassium hexacyanoferrate(III)

Electrochemical impedance spectroscopy

Material safety data sheet

Scanning electron microscopy

Cyclic voltammetry

Differential pulse voltammetry

Codeine

Epinephrine

Acetaminophen

Ascorbic acid

Uric acid

Relative standard deviation

Paulus, W., Bötzel, K., Plendl, H. & Straube, A. Specificity of sumatriptan for abortion of migraine attacks. Lancet (British Edition) 335, 51 (1990).

CAS Google Scholar

Moffat, A. C., Osselton, M. D., Widdop, B. & Watts, J. Clarke’s Analysis of Drugs and Poisons Vol. 3 (Pharmaceutical Press, London, 2011).

Google Scholar

Seo, J. J. et al. Rapid determination of sumatriptan in human plasma by ultra performance liquid chromatography–tandem mass spectrometry and its application to clinical pharmacokinetic study. J. Chromatogr. B 919–920, 38–42. https://doi.org/10.1016/j.jchromb.2013.01.004 (2013).

Article CAS Google Scholar

Flexman, A., Schwarz, S. & Del Vicario, G. An unusual cause of dark blood aspiration during arterial cannulation: Intraoperative detection of sulfhemoglobinemia in a patient taking sumatriptan. Can. J. Anaesth. 54, 44101–44101 (2007).

Article Google Scholar

Ravi, S., Darwis, Y. & Khan, N. Development and validation of an RP-HPLC-UV method for analysis of sumatriptan succinate in pharmaceutical dosage forms. Acta Chromatogr. 21, 421–432 (2009).

Article CAS Google Scholar

Boulton, D. W., Duncan, G. F. & Vachharajani, N. N. Validation and application of a high-performance liquid chromatography/tandem mass spectrometry assay for sumatriptan in human plasma. Biomed. Chromatogr. 17, 48–52 (2003).

Article CAS PubMed Google Scholar

McLoughlin, D., Olah, T., Ellis, J., Gilbert, J. & Halpin, R. Quantitation of the 5HT1D agonists MK-462 and sumatriptan in plasma by liquid chromatography-atmospheric pressure chemical ionization mass spectrometry. J. Chromatogr. A 726, 115–124 (1996).

Article CAS PubMed Google Scholar

Reddy, Y. R., Kumar, K. K., Reddy, M. & Mukkanti, K. Rapid simultaneous determination of sumatriptan succinate and naproxen sodium in combined tablets by validated ultra performance liquid chromatographic method. J. Anal. Bioanal. Techn. 2, 1–6 (2011).

Article Google Scholar

Shah, C., Suhagia, B., Shah, N. & Shah, R. Development and validation of a HPTLC method for the estimation of sumatriptan in tablet dosage forms. Indian J. Pharm. Sci. 70, 831 (2008).

Article CAS PubMed PubMed Central Google Scholar

Al Azzam, K. M., Saad, B., Tat, C. Y., Mat, I. & Aboul-Enein, H. Y. Stability-indicating micellar electrokinetic chromatography method for the analysis of sumatriptan succinate in pharmaceutical formulations. J. Pharmaceut. Biomed. Anal. 56, 937–943 (2011).

Article CAS Google Scholar

Ayad, M., Abdellatef, H., Hosny, M. & Kabil, N. Conductometric determination of certain pharmacological drugs using silver and bismuth. Int. Res. J. Pharmaceut. Appl. Sci. 3, 140–148 (2013).

Google Scholar

Solanki, S. D., Patel, P. & Suhagiya, B. Development and validation of spectrophotometric method for simultaneous estimation of sumatriptan succinate and naproxen sodium in pharmaceutical dosage form. JPSBR 1, 50–53 (2011).

Google Scholar

Ayad, M., Abdellatef, H., Hosny, M. & Kabil, N. Utility of molybdophosphoric acid in qualitative and quantitative analysis of Sibutramine HCl, Sumatribtan succinate and Lomefloxacine HCl. Int. J. Pharmaceut. Biomed. Res. 3, 121–126 (2012).

CAS Google Scholar

Altria, K. & Filbey, S. In Analytical Proceedings. 363–365.

Azizi, B., Farhadi, K. & Samadi, N. Functionalized carbon dots from zein biopolymer as a sensitive and selective fluorescent probe for determination of sumatriptan. Microchem. J. 146, 965–973 (2019).

Article CAS Google Scholar

Sagar, K., Alvarez, J. M. F., Hua, C., Smyth, M. R. & Munden, R. Differential pulse voltammetric determination of sumatriptan succinate (1:1) in a tablet dosage form. J. Pharm. Biomed. Anal. 10, 17–21 (1992).

Article CAS PubMed Google Scholar

Ghalkhani, M., Shahrokhian, S. & Ghorbani-Bidkorbeh, F. Voltammetric studies of sumatriptan on the surface of pyrolytic graphite electrode modified with multi-walled carbon nanotubes decorated with silver nanoparticles. Talanta 80, 31–38 (2009).

Article CAS PubMed Google Scholar

Amiri, M., Pakdel, Z., Bezaatpour, A. & Shahrokhian, S. Electrocatalytic determination of sumatriptan on the surface of carbon-paste electrode modified with a composite of cobalt/Schiff-base complex and carbon nanotube. Bioelectrochemistry 81, 81–85 (2011).

Article CAS PubMed Google Scholar

Rezk, M. R., Michael, A. M., Lotfy, H. M. & Shehata, M. A. Validation of selective electrochemical method for determination of sumatriptan in combined dosage form. Anal. Bioanal. Electrochem. 4, 553–563 (2012).

Google Scholar

Gholivand, M. B. & Mohammadi-Behzad, L. Fabrication of a highly sensitive sumatriptan sensor based on ultrasonic-electrodeposition of Pt nanoparticles on the ZrO2 nanoparticles modified carbon paste electrode. J. Electroanal. Chem. 712, 33–39 (2014).

Article CAS Google Scholar

Shahrokhian, S., Kamalzadeh, Z. & Saberi, R.-S. Glassy carbon electrode modified with a bilayer of multi-walled carbon nanotube and polypyrrole doped with new coccine: Application to the sensitive electrochemical determination of sumatriptan. Electrochim. Acta 56, 10032–10038 (2011).

Article CAS Google Scholar

Karim-Nezhad, G., Khanaliloo, S., Khorablou, Z. & Dorraji, P. S. Signal amplification for sumatriptan sensing based on polymeric surface decorated with Cu nanoparticles. J. Serb. Chem. Soc. 83, 449–462 (2018).

Article CAS Google Scholar

Kalambate, P. K., Sinha, A., Li, Y., Shen, Y. & Huang, Y. An electrochemical sensor for ifosfamide, acetaminophen, domperidone, and sumatriptan based on self-assembled MXene/MWCNT/chitosan nanocomposite thin film. Microchim. Acta 187, 1–12 (2020).

Article Google Scholar

Erdem, A., Eksin, E., Kesici, E., Yaralı, E. & Kanat, E. Single-use sensor technology for monitoring of zearalenone in foods: ZentoSens. Microchem. J. 147, 37–42 (2019).

Article CAS Google Scholar

Martins, T. S., Bott-Neto, J. L., Raymundo-Pereira, P. A., Ticianelli, E. A. & Machado, S. A. An electrochemical furosemide sensor based on pencil graphite surface modified with polymer film Ni-salen and Ni(OH)2/C nanoparticles. Sens. Actuat. B Chem. 276, 378–387 (2018).

Article CAS Google Scholar

Sharma, S., Jain, R. & Raja, A. N. pencil graphite electrode: An emerging sensing material. J. Electrochem. Soc. 167, 037501 (2019).

Google Scholar

Bayraktepe, D. E., İnal, E. K. & Yazan, Z. Preparation and characterization of a pencil graphite electrode modified with gold nanoparticles decorated poly(l-methionine) and its use in the simultaneous sensitive electrochemical analysis of ascorbic acid, acetaminophen, chlorpheniramine maleate, and caffeine. Microchem. J. 171, 106812 (2021).

Article Google Scholar

Oghli, A. H. & Soleymanpour, A. One-step electrochemical modification of pencil graphite electrode with reduced graphene oxide/phosphotungstic acid/sol–gel, and its application to the trace analysis of lead(II). Microchem. J. 173, 107034 (2022).

Article Google Scholar

Arabali, V., Malekmohammadi, S. & Karimi, F. Surface amplification of pencil graphite electrode using CuO nanoparticle/polypyrrole nanocomposite: A powerful electrochemical strategy for determination of tramadol. Microchem. J. 158, 105179 (2020).

Article CAS Google Scholar

Baccarin, M., Ciciliati, M. A., Oliveira, O. N. Jr., Cavalheiro, E. T. & Raymundo-Pereira, P. A. Pen sensor made with silver nanoparticles decorating graphite-polyurethane electrodes to detect bisphenol-A in tap and river water samples. Mater. Sci. Eng. C 114, 110989 (2020).

Article CAS Google Scholar

Rana, A. & Kawde, A. N. Novel electrochemically treated graphite pencil electrode surfaces for the determination of trace α-naphthol in water samples. J. Chin. Chem. Soc. 63, 668–676 (2016).

Article CAS Google Scholar

Buleandră, M., Popa, D. E., David, I. G. & Ciucu, A. A. A simple and efficient cyclic square wave voltammetric method for simultaneous determination of epinephrine and norepinephrine using an activated pencil graphite electrode. Microchem. J. 160, 105621 (2021).

Article Google Scholar

Fan, X. et al. Amperometric sensor for dopamine based on surface-graphenization pencil graphite electrode prepared by in-situ electrochemical delamination. Microchim. Acta 186, 1–8 (2019).

Article ADS Google Scholar

Oghli, A. H., Alipour, E. & Asadzadeh, M. Development of a novel voltammetric sensor for the determination of methamphetamine in biological samples on the pretreated pencil graphite electrode. RSC Adv. 5, 9674–9682 (2015).

Article ADS CAS Google Scholar

Mehmandoust, M., Uzcan, F., Soylak, M. & Erk, N. Dual-response electrochemical electrode for sensitive monitoring of topotecan and mitomycin as anticancer drugs in real samples. Chemosphere 291, 132809 (2022).

Article ADS CAS PubMed Google Scholar

Mehmandoust, M., Karimi, F. & Erk, N. A zinc oxide nanorods/molybdenum disulfide nanosheets hybrid as a sensitive and reusable electrochemical sensor for determination of anti-retroviral agent indinavir. Chemosphere 300, 134430 (2022).

Article ADS CAS PubMed Google Scholar

Mehmandoust, M., Erk, N., Naser, M. & Soylak, M. Molecularly imprinted polymer film loaded on the metal–organic framework with improved performance using stabilized gold-doped graphite carbon nitride nanosheets for the single-step detection of Fenamiphos. Food Chem. 404, 134627 (2023).

Article CAS PubMed Google Scholar

Mehmandoust, M., Çakar, S., Özacar, M. & Erk, N. The determination of timolol maleate using silver/tannic acid/titanium oxide nanocomposite as an electrochemical sensor in real samples. Electroanalysis 34, 1150–1162 (2022).

Article CAS Google Scholar

Mehmandoust, M. et al. An electrochemical sensing platform with a molecularly imprinted polymer based on chitosan-stabilized metal@metal-organic frameworks for topotecan detection. Microchim. Acta 190, 142 (2023).

Article CAS Google Scholar

Adarakatti, P. S. & Patri, S. B. In Electrochemistry 84–129 (2021).

Adarakatti, P. S. & Devaramani, S. In Electrochemistry 44–83 (2021).

Adarakatti, P. S., Sureshkumar, K. & Ramakrishnappa, T. In Carbon Nanomaterials-Based Sensors 149–165 (Elsevier, 2022).

Anik, Ü., Timur, S. & Dursun, Z. Metal organic frameworks in electrochemical and optical sensing platforms: A review. Microchim. Acta 186, 196 (2019).

Article Google Scholar

Habibi, B., Pashazadeh, S., Saghatforoush, L. A. & Pashazadeh, A. Direct electrochemical synthesis of the copper based metal-organic framework on/in the heteroatoms doped graphene/pencil graphite electrode: Highly sensitive and selective electrochemical sensor for sertraline hydrochloride. J. Electroanal. Chem. 888, 115210 (2021).

Article CAS Google Scholar

Jin, Y. et al. Fast cathodic reduction electrodeposition of a binder-free cobalt-doped Ni-MOF film for directly sensing of levofloxacin. J. Alloys Compd. 851, 156823. https://doi.org/10.1016/j.jallcom.2020.156823 (2021).

Article CAS Google Scholar

Tajik, S., Shahsavari, M., Sheikhshoaie, I., Garkani Nejad, F. & Beitollahi, H. Voltammetric detection of sumatriptan in the presence of naproxen using Fe3O4@ZIF-8 nanoparticles modified screen printed graphite electrode. Sci. Rep. https://doi.org/10.1038/s41598-021-98598-1 (2021).

Article PubMed PubMed Central Google Scholar

Naghian, E. et al. A new electrochemical sensor for the detection of fentanyl lethal drug by a screen-printed carbon electrode modified with the open-ended channels of Zn(ii)-MOF. New J. Chem. 44, 9271–9277 (2020).

Article ADS CAS Google Scholar

Zhang, X., Xu, Y. & Ye, B. An efficient electrochemical glucose sensor based on porous nickel-based metal organic framework/carbon nanotubes composite (Ni-MOF/CNTs). J. Alloys Compd. 767, 651–656. https://doi.org/10.1016/j.jallcom.2018.07.175 (2018).

Article CAS Google Scholar

Lu, Z. et al. MOF-derived Co3O4/FeCo2O4 incorporated porous biomass carbon: Simultaneous electrochemical determination of dopamine, acetaminophen and xanthine. J. Alloys Compd. 858, 157701. https://doi.org/10.1016/j.jallcom.2020.157701 (2021).

Article CAS Google Scholar

Wang, M. et al. A novel electrochemical sensor based on MWCNTs-COOH/metal-covalent organic frameworks (MCOFs)/Co NPs for highly sensitive determination of DNA base. Microchem. J. 167, 106336 (2021).

Article CAS Google Scholar

Pashazadeh, S. & Habibi, B. Determination of isoniazid by a copper-based metal-organic frameworks/carbon nitride quantum dots modified pencil graphite electrode as a highly sensitive and selective sensor. J. Electroanal. Chem. 876, 114493 (2020).

CAS Google Scholar

Lee, C.-H. et al. Cooperative effect of unsheltered amide groups on CO2 adsorption inside open-ended channels of a zinc(II)–organic framework. Inorgan. Chem. 52, 3962–3968 (2013).

Article CAS Google Scholar

Lee, C.-H. et al. Amide-containing zinc(II) metal–organic layered networks: A structure–CO2 capture relationship. Inorgan. Chem. Front. 2, 477–484 (2015).

Article ADS CAS Google Scholar

Zheng, B., Bai, J., Duan, J., Wojtas, L. & Zaworotko, M. J. Enhanced CO2 binding affinity of a high-uptake rht-type metal−organic framework decorated with acylamide groups. J. Am. Chem. Soc. 133, 748–751 (2011).

Article CAS PubMed Google Scholar

Khorablou, Z., Shahdost-fard, F. & Razmi, H. Flexible and highly sensitive methadone sensor based on gold nanoparticles/polythiophene modified carbon cloth platform. Sens. Actuat. B Chem. 344, 130284 (2021).

Article CAS Google Scholar

Gahlot, S., Yadav, V., Sharma, P. P. & Kulshrestha, V. Zn-MOF@SPES composite membranes: Synthesis, characterization and its electrochemical performance. Sep. Sci. Technol. 54, 377–385 (2019).

Article CAS Google Scholar

Materials Studio v. 8.0.0.843 (Accelrys, 2014).

Young, R. A. The Rietveld Method (Oxford University Press, London, 1993).

Google Scholar

Rietveld, H. M. A profile refinement method for nuclear and magnetic structures. J. Appl. Crystallogr. 2, 65–71. https://doi.org/10.1107/s0021889869006558 (1969).

Article CAS Google Scholar

Naghdi, S. et al. Selective ligand removal to improve accessibility of active sites in hierarchical MOFs for heterogeneous photocatalysis. Nat. Commun. 13, 1–12 (2022).

Article Google Scholar

Magar, H. S., Hassan, R. Y. & Mulchandani, A. Electrochemical impedance spectroscopy (EIS): Principles, construction, and biosensing applications. Sensors 21, 6578 (2021).

Article ADS CAS PubMed PubMed Central Google Scholar

Ramanavicius, A., Genys, P. & Ramanaviciene, A. Electrochemical impedance spectroscopy based evaluation of 1, 10-phenanthroline-5, 6-dione and glucose oxidase modified graphite electrode. Electrochim. Acta 146, 659–665 (2014).

Article CAS Google Scholar

Lillie, G., Payne, P. & Vadgama, P. Electrochemical impedance spectroscopy as a platform for reagentless bioaffinity sensing. Sens. Actuat. B Chem. 78, 249–256 (2001).

Article CAS Google Scholar

Hu, C., Yuan, S. & Hu, S. Studies on electrochemical properties of MWNTs-Nafion composite films based on the redox behavior of incorporated Eu3+ by voltammetry and electrochemical impedance spectroscopy. Electrochim. Acta 51, 3013–3021 (2006).

Article CAS Google Scholar

Karim-Nezhad, G., Khorablou, Z. & Dorraji, P. S. Applications of polymer and nanoscale carbon-based materials in piroxicam sensing and detection. Sens. Lett. 15, 282–288 (2017).

Article Google Scholar

Akhoundian, M., Alizadeh, T. & Pan, G. Fabrication of the enzyme-less voltammetric bilirubin sensor based on sol–gel imprinted polymer. Electroanalysis 32, 479–488 (2020).

Article CAS Google Scholar

Kokab, T. et al. Tripeptide derivative-modified glassy carbon electrode: A novel electrochemical sensor for sensitive and selective detection of Cd2+ ions. ACS Omega 5, 10123–10132 (2020).

Article CAS PubMed PubMed Central Google Scholar

Espinoza, E. M. et al. Practical aspects of cyclic voltammetry: How to estimate reduction potentials when irreversibility prevails. Journal of The Electrochemical Society 166, H3175 (2019).

Article CAS Google Scholar

Download references

The authors gratefully acknowledge the Research Council of Payame Noor University for their financial support.

Department of Chemistry, Payame Noor University, P.O. Box 19395-4697, Tehran, Iran

Lotfali Saghatforoush, Tohid Mahmoudi & Akbar Bakhtiari

Sharif Energy, Water and Environment Institute (SEWEI), Sharif University of Technology, P.O. Box 11155-8639, Tehran, Iran

Zeynab Khorablou & Seyed Ali Akbar Sajadi

Department of Electrical and Computer Engineering, University of Tabriz, Tabriz, Iran

Hassan Nasiri

You can also search for this author in PubMed Google Scholar

You can also search for this author in PubMed Google Scholar

You can also search for this author in PubMed Google Scholar

You can also search for this author in PubMed Google Scholar

You can also search for this author in PubMed Google Scholar

You can also search for this author in PubMed Google Scholar

L.S.: Conceptualization, Funding acquisition, Supervision, Project administration, Resources, Formal analysis, Validation, writing—original draft, writing—review and editing; T.M.: Conceptualization, Investigation, Methodology, Data curation, Visualization, Formal analysis, Validation, writing—original draft, writing—review and editing; Z.K.: Conceptualization, Resources, Software, Investigation, Methodology, Data curation, Visualization, Formal analysis, Validation, writing—original draft, writing—review and editing; H.N.: Conceptualization, Investigation, Methodology, Data curation, Visualization, Formal analysis, Validation, writing—original draft, writing—review and editing; A.B.: Formal analysis, Validation, writing—original draft, writing—review and editing; S.A.A.S.: Formal analysis, Validation, writing—original draft, writing—review and editing.

Correspondence to Lotfali Saghatforoush.

The authors declare no competing interests.

Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.

Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons licence, and indicate if changes were made. The images or other third party material in this article are included in the article's Creative Commons licence, unless indicated otherwise in a credit line to the material. If material is not included in the article's Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this licence, visit http://creativecommons.org/licenses/by/4.0/.

Reprints and Permissions

Saghatforoush, L., Mahmoudi, T., Khorablou, Z. et al. Electro-oxidation sensing of sumatriptan in aqueous solutions and human blood serum by Zn(II)-MOF modified electrochemical delaminated pencil graphite electrode. Sci Rep 13, 16803 (2023). https://doi.org/10.1038/s41598-023-44034-5

Download citation

Received: 20 June 2023

Accepted: 03 October 2023

Published: 05 October 2023

DOI: https://doi.org/10.1038/s41598-023-44034-5

Anyone you share the following link with will be able to read this content:

Sorry, a shareable link is not currently available for this article.

Provided by the Springer Nature SharedIt content-sharing initiative

By submitting a comment you agree to abide by our Terms and Community Guidelines. If you find something abusive or that does not comply with our terms or guidelines please flag it as inappropriate.